The BHG-106 is the Barkbusters mounting kit designed for Beta RR Enduro, RR Racing and Xtrainer models from 2021 onward. It is the structure onto which Barkbusters plastics are mounted: on its own, it protects levers and hands from impacts; with the plastics fitted, it also shields against branches, mud and cold.

Important to know before purchase: installation requires opening the grips if they are closed at the ends and shortening the plastic throttle tube end cap by no more than 3 mm. This is workshop-level work.

Key features

• Heat-treated aluminium bars, right and left.
• Two-point mounting: with an expander and collar at the handlebar end, and on a split clamp around the tapered section.
• Bar-end weights not included: the parts list includes expanders, collars and nuts.
• Compatible with JET-003, VPS-003, STM-003 and BCF-003 plastics, sold separately.

Protection and use

Barkbusters clearly distinguishes between its two mounting configurations, and the two-point configuration, anchored both at the end and at the centre of the handlebar, is the one the manufacturer specifies for impact protection. On Beta enduro bikes, this means protecting the brake and clutch levers from falls, logs and branches.

Materials and construction

Heat-treated aluminium bars (manufacturer code BAR-V-043), CS-04 split clamps with CP5 connectors, and BBE14A expanders with BBEC5M collars. The manufacturer does not state the finish or weight of the kit, so we do not list them.

Compatibility

Do you have a Beta RR X Pro? It is not listed for this code: from 2025, Barkbusters covers it with the BHG-157, which is currently not listed in the Endurrad catalogue.

Barkbusters states that compatibility applies to motorcycles in original factory configuration. Fitment on aftermarket handlebars must be checked before purchase.

Installation

Preparation. If the grips are closed at the ends, open them with a utility knife; on the right side, the hole must be clean and no smaller than the throttle tube's internal diameter. Move the throttle assembly approximately 20 mm outward, roll back the grip and use a hacksaw to cut the plastic throttle tube end cap: no more than 3 mm, without touching the handlebar. Remove any burrs before reassembly so the throttle moves freely. Barkbusters also publishes an installation video on its website.

Fitting. Install the clamp without tightening it, with the rings of the two halves aligned and facing toward the centre of the motorcycle. Secure the bar at the end and to the connector, horizontal when viewed from the side, and tighten in this order: M8x45 end screw, M8x25 bar screw, M6x25 screw securing the connector, M6x30 screw closing the clamp. The nut fits into its recess and does not need to be held with a wrench.

Specified torque settings: 10 Nm for the M6 screws, 28 Nm for the M8 screws and 21 Nm for the collar, using medium-strength threadlocker and checking again after the first 50 km. With heated grips, the instructions state that approximately 3 mm of washers may be needed to maintain clearance from the throttle grip.

What is included

• 2 aluminium bars, right and left
• 4 clamp halves and 2 connectors for the clamps
• 2 expanders, 2 collars and 2 conical nuts
• Fasteners: 2 M8x45 countersunk screws, 2 M8x25 button-head screws, 2 M6x25 screws, 2 M6x30 screws and 4 M6 self-locking nuts
• Official INS-BHG-106 instructions

What is NOT included

• Protection plastics. The kit is the structure only: the plastics must be purchased separately from the options specified by the manufacturer.
• Handlebar weights: they are not included in the parts list.
• Washers that may be required with heated grips, threadlocker and tools.

Plastics to pair with the kit

• JET-003: compact profile, for enduro and off-road riding.
• VPS-003: deflector adjustable to two positions. It is being phased out, and the price list indicates VPS-203 as its replacement.
• STM-003, STORM series: more extensive coverage, for colder months.
• BCF-003, CARBON series: made from carbon fibre.

Why choose Barkbusters

Barkbusters is an Australian brand owned by Rideworx Pty Ltd, specialising in motorcycle handguards. Each application-specific kit is designed around the geometry of a specific handlebar, with a published parts list and an installation PDF detailing the fasteners, sequence and torque settings. The structure and plastics remain separate: you can change the plastic series or colour without replacing the kit.

Why buy it from Endurrad

On Endurrad, every Barkbusters product page states the exact code, the years covered and what is actually in the box, with the official instructions available to download before purchase. You can find the full range in the Barkbusters collection.