{"product_id":"kit-paramani-barkbusters-honda-crf300-rally-bhg-093","title":"Barkbusters BHG-093 handguard mounting kit for Honda CRF300 Rally from 2021","description":"\u003cp\u003eThe \u003cstrong\u003eBHG-093\u003c\/strong\u003e is the Barkbusters mounting kit designed around the handlebar geometry of the \u003cstrong\u003eHonda CRF300 Rally from 2021 onward\u003c\/strong\u003e. It is the aluminum structure that supports the handguards: it protects your hands, levers, and controls from branches, loose stones, and falls, and stays on the motorcycle even when you change the plastics.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCRF300 Rally only, not CRF300L.\u003c\/strong\u003e The two motorcycles share their engine and chassis, but the Rally has fairing and a windscreen, and the clamp must accommodate them: for the CRF300L, the manufacturer specifies a different code, \u003ca href=\"\/en\/products\/kit-paramani-barkbusters-honda-crf300l-bhg-091\"\u003eBHG-091\u003c\/a\u003e. This is the most common purchasing mistake with these two motorcycles.\u003c\/p\u003e\n\u003cp\u003eAs with the entire range, \u003cstrong\u003ethe structure and protective plastics are two separate products\u003c\/strong\u003e: here you are purchasing the structure only, with hardware and handlebar weights.\u003c\/p\u003e\n\n\u003ch2\u003eKey features\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo-point mounting\u003c\/strong\u003e — anchoring at the handlebar end plus a clamp on the straight section. This is the configuration the manufacturer specifies for impact protection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeat-treated aluminum bar\u003c\/strong\u003e, with a wraparound design and natural aluminum finish.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHandlebar weights included\u003c\/strong\u003e — unlike the CRF300L version.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecific to the Rally\u003c\/strong\u003e, designed to accommodate the stock fairing and windscreen.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterchangeable plastics\u003c\/strong\u003e — compatible with JET, VPS, STORM, and CARBON, each sold separately.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade in Australia\u003c\/strong\u003e by Rideworx Pty Ltd.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eProtection and use\u003c\/h2\u003e\n\u003cp\u003eThe CRF300 Rally is bought for going far on roads that eventually run out: a large tank, a windscreen, and the idea of loading it up and setting off. In that kind of use, your hands are the most exposed part — branches, loose stones, and the stationary fall that happens to everyone when the motorcycle is loaded. The stock handguards are plastic and have no internal structure: they shield you from the wind, but in a fall they bend together with the lever. Two-point mounting does a different job: the aluminum bar forms a cage around your hand and transfers the impact to the structure. A thousand kilometers from home, that is the difference between carrying on and looking for a workshop. The \u003cem\u003esingle-point\u003c\/em\u003e configuration, the other option in the range, is specified by the manufacturer only for protection from wind and weather.\u003c\/p\u003e\n\n\u003ch2\u003eMaterials and construction\u003c\/h2\u003e\n\u003cp\u003eThe structure is made of heat-treated aluminum, a process the manufacturer uses to increase strength and impact absorption capacity. The design is wraparound: it starts at the straight section of the handlebar, curves around the hand, and closes at the end. The clamp and bar curve are calculated around the Rally's dimensions.\u003c\/p\u003e\n\n\u003ch2\u003eCompatibility\u003c\/h2\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eYears\u003c\/th\u003e\n\u003cth\u003eBarkbusters code\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eHonda\u003c\/td\u003e\n\u003ctd\u003eCRF300 Rally\u003c\/td\u003e\n\u003ctd\u003efrom 2021 onward\u003c\/td\u003e\n\u003ctd\u003eBHG-093-NP\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003csmall\u003eCompatibility specified by Barkbusters for motorcycles in \u003cstrong\u003eoriginal factory configuration\u003c\/strong\u003e. Aftermarket handlebars may have different diameters and wall thicknesses: verify the mounting before purchasing. Unsure about your model? \u003ca href=\"\/en\/pages\/contatti\"\u003eContact us\u003c\/a\u003e with the model and year.\u003c\/small\u003e\u003c\/p\u003e\n\n\u003ch2\u003eInstallation\u003c\/h2\u003e\n\u003cp\u003eMounts to the original handlebar, with no drilling or motorcycle modifications. The stock plastic handguards must be removed, as must the original handlebar weights: the structure anchors precisely at the handlebar ends, and the supplied weights are used in their place.\u003c\/p\u003e\n\u003cp\u003eBefore fully tightening, check that the throttle, front brake, clutch, and engine stop switch operate freely and that the steering turns from lock to lock without interfering with the fairing. Check the tightening again after the first \u003cstrong\u003e50 km\u003c\/strong\u003e, and after every fall. The complete procedure and warnings are provided in the official instructions \u003cstrong\u003eINS-BHG-093-NP\u003c\/strong\u003e, attached to this product page in the Manufacturer documents section.\u003c\/p\u003e\n\n\u003ch2\u003eWhat you will find in the package\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eTwo heat-treated aluminum bars\u003c\/li\u003e\n\u003cli\u003eClamps for the straight section of the handlebar\u003c\/li\u003e\n\u003cli\u003eComplete mounting hardware\u003c\/li\u003e\n\u003cli\u003eHandlebar weights\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhat is NOT included\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtective plastics.\u003c\/strong\u003e They must be selected and ordered separately from the \u003ca href=\"\/en\/collections\/barkbusters-plastiche\"\u003eJET, VPS, STORM, and CARBON\u003c\/a\u003e series. EGO plastics are not compatible with this structure.\u003c\/li\u003e\n\u003cli\u003eLED lights and other accessories in the range, which remain separate products.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhy choose Barkbusters\u003c\/h2\u003e\n\u003cp\u003eBarkbusters is a Rideworx Pty Ltd brand, an Australian company that has designed and produced motorcycle handguards since 1984. The catalog distinguishes between the CRF300L and CRF300 Rally with two different codes even though the two motorcycles are closely related: this is the level of detail that distinguishes a kit designed for a specific motorcycle from an adaptable accessory.\u003c\/p\u003e\n\n\u003ch2\u003eWhy buy it from Endurrad\u003c\/h2\u003e\n\u003cp\u003eEndurrad supplies accessories for touring, adventure, and enduro motorcycles: compatibility verified against the manufacturer's documentation, official instructions attached to the product page, and assistance before purchase if your model is unclear. Free shipping in Italy on orders over €100 and in Europe on orders over €250, returns within 14 days, 1-year warranty. See the full \u003ca href=\"\/en\/collections\/barkbusters\"\u003eBarkbusters range\u003c\/a\u003e.\u003c\/p\u003e","brand":"BARKBUSTERS","offers":[{"title":"Two-point, aluminum","offer_id":56617308750168,"sku":"BR-BHG-093-00-NP","price":124.5,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0604\/6561\/0991\/files\/kit-paramani-barkbusters-bhg-093-honda-crf300-rally-01_83f88d2a-15e0-423a-964c-9c89e75c01a1.jpg?v=1789575691","url":"https:\/\/endurrad.com\/en\/products\/kit-paramani-barkbusters-honda-crf300-rally-bhg-093","provider":"Endurrad®","version":"1.0","type":"link"}