{"product_id":"kit-paramani-barkbusters-ducati-scrambler-1100-desert-sled-bhg-067-bk","title":"Barkbusters BHG-067 handguard mounting kit for Ducati Scrambler 1100 and Desert Sled — black","description":"\u003cp\u003eThe \u003cstrong\u003eBHG-067\u003c\/strong\u003e is the mounting structure that Barkbusters designed for the handlebars of the Ducati Scrambler 1100 and second-generation Scramblers. It is the aluminum base onto which the handguards are mounted: \u003cstrong\u003ethe protective plastics are not included\u003c\/strong\u003e and must be chosen separately, because in the Barkbusters range the structure and protection are two separate, interchangeable products. This is the \u003cstrong\u003eblack\u003c\/strong\u003e version, powder-coated.\u003c\/p\u003e\n\u003ch3\u003eMain features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo mounting points\u003c\/strong\u003e: the bar is secured to the end of the handlebar and to a clamp on the straight section. This is the configuration the manufacturer specifies for impact protection; the \u003cem\u003esingle-point\u003c\/em\u003e configuration, the other option in the range, is intended only for wind and weather protection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDedicated multi-fit clamps\u003c\/strong\u003e, one left and one right, with connectors designed for each side.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWraparound heat-treated aluminum bar\u003c\/strong\u003e, which acts as a structural element in front of the levers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour plastic series on the same base\u003c\/strong\u003e: JET, VPS, STORM or CARBON, also interchangeable later.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eYears\u003c\/th\u003e\n\u003cth\u003eCode\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDucati\u003c\/td\u003e\n\u003ctd\u003eScrambler Full Throttle\u003c\/td\u003e\n\u003ctd\u003efrom 2015\u003c\/td\u003e\n\u003ctd\u003eBHG-067\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDucati\u003c\/td\u003e\n\u003ctd\u003eScrambler Flat Track Pro\u003c\/td\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eBHG-067\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDucati\u003c\/td\u003e\n\u003ctd\u003eScrambler Desert Sled\u003c\/td\u003e\n\u003ctd\u003efrom 2017\u003c\/td\u003e\n\u003ctd\u003eBHG-067\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDucati\u003c\/td\u003e\n\u003ctd\u003eScrambler 1100\u003c\/td\u003e\n\u003ctd\u003efrom 2018\u003c\/td\u003e\n\u003ctd\u003eBHG-067\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDucati\u003c\/td\u003e\n\u003ctd\u003eScrambler 1100 Special\u003c\/td\u003e\n\u003ctd\u003efrom 2018\u003c\/td\u003e\n\u003ctd\u003eBHG-067\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDucati\u003c\/td\u003e\n\u003ctd\u003eScrambler 1100 Sport\u003c\/td\u003e\n\u003ctd\u003efrom 2018\u003c\/td\u003e\n\u003ctd\u003eBHG-067\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eBarkbusters states these compatibility details for motorcycles in \u003cstrong\u003eoriginal factory configuration\u003c\/strong\u003e. With an aftermarket handlebar, diameters and wall thicknesses change, so the mounting must be checked before purchase. For the Scrambler Icon, Classic, Urban Enduro and Sixty2, the correct code is not this one but BHG-060.\u003c\/p\u003e\n\u003ch3\u003eWhat to know before ordering if you have a Desert Sled\u003c\/h3\u003e\n\u003cp\u003eThe official instructions state that on the \u003cstrong\u003eDesert Sled\u003c\/strong\u003e, the clutch lever support on the left side must be moved inward by \u003cstrong\u003e15 mm\u003c\/strong\u003e, leaving \u003cstrong\u003e35 mm\u003c\/strong\u003e of clearance from the switchgear. Before riding again, check that the lever can be pulled fully without interference. This is not an irreversible modification, but it is an additional step compared with the other models and should be taken into account.\u003c\/p\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eRemove the original plug from the end of the handlebar, position the clamp without tightening it, secure the bar to the end and to the connector, set it horizontally when viewed from the side, and tighten it in the order specified by the manufacturer. Specified torque values: \u003cstrong\u003e10 Nm for the M6 bolts and 28 Nm for the M8 bolts\u003c\/strong\u003e, using medium-strength threadlocker, then check again after the first 50 km.\u003c\/p\u003e\n\u003cp\u003eLeave approximately 3 mm of clearance between the throttle grip and the handguard so the throttle can close freely, and check the throttle, front brake, clutch and engine kill switch with the handlebars turned freely from lock to lock. Installing handguards is considered a safety-critical procedure: if you are not experienced, have it carried out by a technician.\u003c\/p\u003e\n\u003ch3\u003eWhat you will find in the package\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTwo aluminum bars, one left and one right\u003c\/li\u003e\n\u003cli\u003eTwo multi-fit clamps and two connectors, left and right\u003c\/li\u003e\n\u003cli\u003eTen screws and two M6 self-locking nuts\u003c\/li\u003e\n\u003cli\u003eTwo sets for mounting to the bar ends: collar, expander, clamp and conical ring\u003c\/li\u003e\n\u003cli\u003eOfficial INS-BHG-067-BK instructions, downloadable from this page\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe manufacturer states that some parts are not needed on every model: the collar is not used on the Desert Sled, and the clamp is not used on the 1100 models. It is normal for some parts to remain unused.\u003c\/p\u003e\n\u003ch3\u003eWhat is NOT included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtective plastics\u003c\/strong\u003e, to be chosen from JET, VPS, STORM and CARBON\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHandlebar weights\u003c\/strong\u003e: they are not included in the official parts list\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy Barkbusters\u003c\/h3\u003e\n\u003cp\u003eBarkbusters is an Australian brand of Rideworx Pty Ltd that has been producing handguards for over thirty years and states compatibility model by model and year by year. Each kit comes with official instructions including a parts list, installation sequence and tightening torques: this documentation lets you know, before buying, what is in the box and how it is installed.\u003c\/p\u003e\n\u003ch3\u003eWhy buy it from Endurrad\u003c\/h3\u003e\n\u003cp\u003eAt Endurrad, you can find the structure and compatible plastics in one place, along with the compatibility table and official PDF on the page. If you have any doubts about your model year or configuration, ask before ordering: we prefer one extra email to a return.\u003c\/p\u003e","brand":"BARKBUSTERS","offers":[{"title":"Two attachment points","offer_id":56617437364568,"sku":"BR-BHG-067-00-BK","price":152.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0604\/6561\/0991\/files\/kit-paramani-barkbusters-ducati-scrambler-1100-bhg-067-nero-struttura-01.jpg?v=1789816105","url":"https:\/\/endurrad.com\/en\/products\/kit-paramani-barkbusters-ducati-scrambler-1100-desert-sled-bhg-067-bk","provider":"Endurrad®","version":"1.0","type":"link"}